USB Device of current status detected (WTF)

2008-11-17 12:33:06

#1

Gooners: Wiki Contributor; +2,700|6898

I'm getting an error message when booting up:
USB Device of current status detected

Specs:

Asus Rampage Formula X48
C2Q Q9450
HD3870X2 1GB
4GB of OCZ reaper 1066 MHz RAM

So Far I've trued resetting the CMOS, and that didn't do anything.

All I did was put in my sony ericcson usb cable for my phone this morning while booting, and it gave me tat message, everything was working yesterday.

2008-11-17 12:38:01

#2

.Sup: be nice; +2,646|6719|The Twilight Zone

Try disabling USB legacy support in BIOS

https://www.shrani.si/f/3H/7h/45GTw71U/untitled-1.png

2008-11-17 12:38:41

#3

Gooners: Wiki Contributor; +2,700|6898

i can't enter bios

2008-11-17 12:48:39

#4

Gooners: Wiki Contributor; +2,700|6898

Ok i jsut remove the cmos battery

I put the CMOS Battery back in, and I get another message (on top of the initial one) saying CMOS Checksum bad

WTF

Last edited by Gooners (2008-11-17 12:57:27)

2008-11-17 13:14:50

#5

mr.hrundi: Wurstwassereis; +68|6703|Germany

it says that when the power to the CMOS is cut off. somewhere it should say "load defaults" or something like that. select that and it should boot with the default settings.

2008-11-17 13:17:41

#6

Gooners: Wiki Contributor; +2,700|6898

I can't get into the BIOS, and i sort of panicing now.

Ive removed the battery twice, and used the Clr CMOS button.

Neither work.

What do i do.

2008-11-17 13:26:08

#7

mr.hrundi: Wurstwassereis; +68|6703|Germany

Well, I guess I can't help you then, I'm sorry.

For the pros out there it might be helpful to know what the screen says exactly when you press the power button (or if it makes any beeps).

2008-11-17 13:29:58

#8

Gooners: Wiki Contributor; +2,700|6898

No beeps,a nd it loads up normally till i get the error

2008-11-18 05:45:28

#9

mr.hrundi: Wurstwassereis; +68|6703|Germany

I don't know if you already solved the problem, but here are a few more things you could try:

if the message CMOS-checksum bad appeares, try pressing F1. for some mainboards this is the command to start booting with default settings.

make sure the battery is put in correctly (+ and -) and make sure the contact is really touching the battery

There sometimes is a thing called Jumper next to the battery, which does the same as the small button you said you pressed. Did you do anything with that jumper?

try a new battery

what happened to my old PC was that there was a microscopic crack on the mainboard near the BIOS-chip. It now only works when I push and pull the mainboard a little bit before booting.

Last edited by mr.hrundi (2008-11-18 05:46:03)

2008-11-18 14:17:09

#10

Gooners: Wiki Contributor; +2,700|6898

Well I couldn't access the BIOS.

And the CMOS CLR button wouldn't work.

So .Sup (<3) told me to remove the CMOS Battery, and i put it back the next day, and I could finally get in.

Thx guys (even though i barely got any help )

2008-11-18 18:23:22

#11

some_random_panda: Flamesuit essential; +454|6657

Why didn't you just short the connectors?

Or is that only for my motherboard?

2008-11-18 18:27:29

#12

bad-man: now say you sorry; +34|6114|one windy city

found this on another forum
"Check all USB jumpers

I just assembled a system with a ASUS P5K-VM board, and when I first booted it, I got the "USB Device Over Current Status Detected !!" error. After 2.5 hours of trying everything, I noticed a blue jumper lying in the box the board came in. The jumper was used to select if the USB-port is on when the PC is off. When I connected the jumper, the system worked."

2008-11-18 18:39:22

#13

Brasso: member; +1,549|6896

some_random_panda wrote:
Why didn't you just short the connectors?

Or is that only for my motherboard?

jumpers are too tricky for my big thumbs to deal with, i just stick to cycling the battery

"people in ny have a general idea of how to drive. one of the pedals goes forward the other one prevents you from dying"

2008-11-18 18:42:01

#14

Gooners: Wiki Contributor; +2,700|6898

bad-man wrote:
found this on another forum
"Check all USB jumpers

I just assembled a system with a ASUS P5K-VM board, and when I first booted it, I got the "USB Device Over Current Status Detected !!" error. After 2.5 hours of trying everything, I noticed a blue jumper lying in the box the board came in. The jumper was used to select if the USB-port is on when the PC is off. When I connected the jumper, the system worked."

I checked that too, but it didn't do anything.

2008-11-19 17:19:20

#15

bad-man: now say you sorry; +34|6114|one windy city

try this.. looks like lots of peepz are having similar problems .. oh and the error message is
USB Device Over Current Status Detected and not USB Device of current status detected

anywho... good luck

http://forums.pcpitstop.com/lofiversion … 48020.html

BF2S Forums USB Device of current status detected (WTF)

some_random_panda wrote:

bad-man wrote:

Board footer