Overclocking E6300

2008-02-25 01:51:00

#1

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

I was trying out that gigabyte easy tune 5 to see how it overclocked. My cpu is 1.86ghz stock so i put the fsb up a little to make it 2.0ghz, then went into bf2 loaded up a server and it was really jumpy like when i run it stops and starts i checked my temps they were like 55C idle and about 65 while gaming. Is that lag from the cpu overheating or because of the easytune 5 program i used?

When i turn the cpu back to 1.86 it goes back to normal btw my mobo is a gigabyte 965P-DS3.

2008-02-25 01:55:27

#2

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

You should OC in BIOS. Forget about those windows based oc programs.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 01:58:08

#3

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

Yea thats what i was getting at to not sure if it was overheating or caused by that program i used. Im only using the stock heatsink on the cpu but is 52C a good temp for idle and about 60ish while gaming.

Last edited by B00MH3ADSH0T (2008-02-25 01:58:25)

2008-02-25 02:11:34

#4

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
Yea thats what i was getting at to not sure if it was overheating or caused by that program i used. Im only using the stock heatsink on the cpu but is 52C a good temp for idle and about 60ish while gaming.

temps are on the high side. My friends E6320 OC'ed to 2.8ghz has load temps of 60c with stock cooler. idles at 40c.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 02:20:02

#5

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

Where do i go to make sure my fan is running at 100% all the time?

2008-02-25 02:25:27

#6

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

There is a page like this is BIOS.

https://www.legitreviews.com/images/reviews/418/health.jpg

Those Smart fan control mode/method settings are where you can change the fan speed.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 02:45:33

#7

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

When i go into the bios the option that says "cpu host frequency" is locked so i cant select it is there anyway to unlock it? also is this the option that changes the fsb?

Last edited by B00MH3ADSH0T (2008-02-25 03:16:49)

2008-02-25 03:19:27

#8

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
When i go into the bios the option that says "cpu host frequency" is locked so i cant select it is there anyway to unlock it? also is this the option that changes the fsb?

Gigabyte boards often have the OC settings 'locked' so users with no knowlegde won't be able to damage the hardware.
FSB settings can be unlocked by pressing Ctrl+F1.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 04:00:49

#9

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

Yea ctrl+f1 unlocks options but still wont let me touch "cpu host frequency"

2008-02-25 04:06:29

#10

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
Yea ctrl+f1 unlocks options but still wont let me touch "cpu host frequency"

you need to set the cpu host clock control enabled first.
http://enthusiast.hardocp.com/image.htm … 9sLmdpZg==

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 04:09:55

#11

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

Just before i enable the clock control it gives me a warning to turn something about the voltage from manual to auto do i do that?

2008-02-25 04:12:18

#12

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
Just before i enable the clock control it gives me a warning to turn something about the voltage from manual to auto do i do that?

assuming it is the CPU vcore voltage, yes. We'll get back to the voltage settings if OC'ed higher than 2.8Ghz.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 04:16:08

#13

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

GC_PaNzerFIN wrote:
B00MH3ADSH0T wrote:
Just before i enable the clock control it gives me a warning to turn something about the voltage from manual to auto do i do that?
assuming it is the CPU vcore voltage, yes. We'll get back to the voltage settings if OC'ed higher than 2.8Ghz.

Yea im only going for about 2.4ghz until i get a better heatsink.

2008-02-25 04:18:15

#14

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
GC_PaNzerFIN wrote:
B00MH3ADSH0T wrote:
Just before i enable the clock control it gives me a warning to turn something about the voltage from manual to auto do i do that?
assuming it is the CPU vcore voltage, yes. We'll get back to the voltage settings if OC'ed higher than 2.8Ghz.
Yea im only going for about 2.4ghz until i get a better heatsink.

The stock can go to 2.8ghz easily. That is at stock voltage.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 04:54:17

#15

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

Yea im not sure what happend i turned on that clock control option and it let me change the fsb but it said "system voltage not optimised" and it was flashing red it said i should turn it from manual to auto but if i do that wont it change the voltages by itself?

2008-02-25 04:59:30

#16

The#1Spot: Member; +105|6818|byah

B00MH3ADSH0T wrote:
GC_PaNzerFIN wrote:
B00MH3ADSH0T wrote:
Just before i enable the clock control it gives me a warning to turn something about the voltage from manual to auto do i do that?
assuming it is the CPU vcore voltage, yes. We'll get back to the voltage settings if OC'ed higher than 2.8Ghz.
Yea im only going for about 2.4ghz until i get a better heatsink.

good idea

2008-02-25 04:59:56

#17

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
Yea im not sure what happend i turned on that clock control option and it let me change the fsb but it said "system voltage not optimised" and it was flashing red it said i should turn it from manual to auto but if i do that wont it change the voltages by itself?

yep. auto means it changes the voltage by itself. I recommend having CPU voltage on auto because that is enough for stock cooler OC.

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 05:16:37

#18

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

when i turned it on auto cpu-z prog said my cpu was like 1.4 voltage or something isnt that dangerous to have it on auto if it changes ur cpu voltage level anyway i have it set on manual as default it said "system voltage level" not cpu voltage tho unless they are the same thing.

2008-02-25 05:45:25

#19

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
when i turned it on auto cpu-z prog said my cpu was like 1.4 voltage or something isnt that dangerous to have it on auto if it changes ur cpu voltage level anyway i have it set on manual as default it said "system voltage level" not cpu voltage tho unless they are the same thing.

yes you can keep CPU voltage as manual and 1.35v. Doing so won't change the NB voltage. You are good to go change the FSB now.

Last edited by GC_PaNzerFIN (2008-02-25 05:45:57)

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 06:22:24

#20

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

anyway so i had it at 2.2ghz and it worked but then i bumped it up to 340 fsb thats 2.380ghz but it crashed on me not sure whats going on there.

2008-02-25 07:01:22

#21

Sydney: 2λчиэλ; +783|7122|Reykjavík, Iceland.

Make sure your memory clocks aren't too fast, that's what happened to me when I was overclocking at first.

2008-02-25 08:11:26

#22

aimless: Member; +166|6403|Texas

Also check to make sure Intel EIST is disabled.

2008-02-25 08:17:32

#23

B00MH3ADSH0T: Fresh NoobCaeks Here; +118|6669|Penrith,Nsw, Aus

PBAsydney wrote:
Make sure your memory clocks aren't too fast, that's what happened to me when I was overclocking at first.

Yea i think this might be the problem because my mobo + cpu should clear 2.4 easily how do i fix the memory clocks? My ram is corsair 2gb XMS2 pc-6400 800mhz 5-5-5-18 frequency is 400mhz fsb:dram is 2:3 according to cpu-z

Last edited by B00MH3ADSH0T (2008-02-25 08:20:40)

2008-02-25 08:21:26

#24

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6693|Finland

B00MH3ADSH0T wrote:
PBAsydney wrote:
Make sure your memory clocks aren't too fast, that's what happened to me when I was overclocking at first.
Yea i think this might be the problem because my mobo + cpu should clear 2.4 easily how do i fix the memory clocks? My ram is corsair 2gb XMS2 pc-6400 800mhz 5-5-5-18 frequency is 400mhz fsb:dram is 2:3 according to cpu-z

change the FSB:RAM ratio to 1:1 and it should work

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2008-02-25 09:54:07

#25

twoblacklines: all grown up now (its boring); +49|6485

my e6300 is running at 2.8ghz will go to 3.4 (on air, tuniq tower 120) but pointless and its well quick on 2.8ghz. Also you hit your memory strap (when memory slows down) at 400fsb on gigabyte boards.

BF2S Forums Overclocking E6300

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

GC_PaNzerFIN wrote:

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

GC_PaNzerFIN wrote:

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

GC_PaNzerFIN wrote:

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

B00MH3ADSH0T wrote:

PBAsydney wrote:

B00MH3ADSH0T wrote:

PBAsydney wrote:

Board footer